For Inquiries send Email: Click Here

1. Shake the storage bottle of DRI WASH 'n GUARD® vigorously for 30 seconds, or until all product that adheres to bottom of storage bottles has mixed in.
2. Pour DRI WASH 'n GUARD® into the AIRosol pump sprayer until the bottle is approximately 3/4 full.
3. The volume of DRI WASH 'n GUARD® is 8 ounces when the bottle is filled to this level.

1. Apply DWG ULTRA-ION™ Waterless Car Wash to a cool, dry surface in a shaded area, out of wind if possible.
2. Use two clean 100% cotton terry cloth towels... one for applying the product and one for buffing.
3. Invert the bottle and shake vigorously for 15-20 seconds.
4. Pressurize the bottle by pumping the cap up and down until a strong resistance is felt (approx. 10-15 times).
5. Spray a light coat of DRI WASH 'n GUARD® on a small section of vehicle (2-3 sq. ft.), spraying with a broad sweeping motion where possible.
6. Using the terry cloth towel, with VERY LIGHT PRESSURE rub DRI WASH 'n GUARD® thoroughly over the sprayed area until the filmy haze that appears almost disappears.
7. Wait 2 to 5 minutes, then buff the remaining haze, using VERY LIGHT PRESSURE, with second 100% cotton terry cloth towel.
8. For Best Results, apply to entire vehicle then buff to high gloss starting with where you first applied the product. This will give the ULTRA-ION™ time to "cure" and lift debris from the surface.
9. To achieve an extremely high gloss finish, buff with a third towel, using VERY LIGHT PRESSURE.

1. Apply DRI WASH 'n GUARD® to a cool, dry surface in a shaded area. Avoid windy conditions if possible.
2. Use two DWG Microfiber Buffing Towels or clean 100% cotton terry cloth towels... one for cleaning/polishing and one for buffing.
3. Invert the bottle and shake vigorously for 15-20 seconds.
4. Pressurize the bottle by pumping the cap up and down until a strong resistance is felt (approx. 10-15 times).
5. Spray a light coat of DRI WASH 'n GUARD® on a small section of vehicle (2-3 sq. ft.), spraying with a broad sweeping motion where possible.
6. With moderately firm pressure, rub DRI WASH 'n GUARD® thoroughly over the sprayed area until the filmy haze that appears almost disappears.
7. Buff the remaining haze to a high gloss with second DWG Microfiber Towel or 100% cotton terry cloth towel.

1. Use a conventional or orbital-type buffer equipped with a foam polishing pad. Do not exceed 2,400 RPM.
2. Apply DRI WASH 'n GUARD® as described in steps 3, 4, and 5 above. Immediately buff sprayed area to a high gloss.
3. Continue, section by section, until all accessible areas have been buffed. Polish any remaining areas by hand, if necessary.

1. Apply DRI WASH 'n GUARD® to a cool, dry surface in a shaded area. Avoid windy conditions if possible.
2. Use two DWG Microfiber Buffing Towels or 100% cotton terry cloth towels... one for cleaning/polishing and one for buffing.
3. Invert aerosol can and shake vigorously for 5 seconds.
4. Spray DRI WASH 'n GUARD® on a small section of vehicle (2-3 sq. ft.), spraying with a broad sweeping motion where possible.
5. With moderately firm pressure, rub DRI WASH 'n GUARD® thoroughly over the sprayed area until the filmy haze that appears almost disappears.
6. Buff the remaining haze to a high gloss with DWG Microfiber Buffing Towel.
7. When finished, invert can and spray for 3 seconds to clear nozzle.